router sr-2501 설정법

설정방법

rot435.str 업데이트 파일

SR2501>
SR2501>
SR2501>
SR2501>
SR2501>
SR2501>
SR2501>
SR2501> admin
Password :
Line Protocol on Interface Serial2 changed state to DOWN
SR2501#
SR2501#
SR2501#
SR2501#
SR2501#
SR2501# ppp disable
SR2501# fr enable
To affect your changing of device driver on port 1,
You should reboot the system after executing the 'write' command without 'saveal
l' command.
To affect your changing of device driver on port 2,
You should reboot the system after executing the 'write' command without 'saveal
l' command.
SR2501# write
BLK#31 erased (delay=61579, 400ms)
SR2501#
SR2501# reset
Reinitializing Processor...!

Hi.
DRAM test...OK!
System Bootstrap, Version 1.0
Copyright (c) 1996 by SsangYong Infomation & Communications Corp.
i960 processor with 8 Mbytes of main memory

Downloading IOS ...from FLASH memory!
!source code format type is COFF
!.text:0x20010000(0xdd1cc) .data:0x200ed1d0(0xe488) .bss:0x200fb660(0x238150)
!<entry point> = 0x20010510

reading SR2501 configuration from NVRAM(60000) ... O.K.
wheap_start = [203337B0] maxaddr = [207FFFFF]
LAN port (0) Initializing ......OK.
WAN port (0) Initializing ......OK.
WAN port (1) Initializing ......OK.

                SsangYong Router System Ver. 4.3.5
                        Compiled

Copyright (C) 1995 RouterWare, Inc.
Copyright (C) 1995 RainbowBridge Communications Inc.
Copyright (C) 1995-1999 SsangYong Information & Communications Corp.

Buffers Initialized
Ethernet initialized
Frame Relay Initialized.
Device Drivers Initialized
IP Disabled.
IPX Disabled.
Spanning Tree is disabled.
BOOTP Disabled.
SNMP disabled.
RIP Disabled.
OSPF Disabled.
Queuing Initialized
SR2501> admin
Password :
SR2501#
Interface Serial1 changed state to UP !
Line Protocol on Interface Serial1 changed state to UP
SR2501#
SR2501#
Frame Relay: Link state set to Up for port 0
SR2501#
SR2501#
SR2501#
SR2501# sh conf

        SsangYong Router System Version 4.3.5
                Compiled by YesHong, 30-MAY-2000
        1 LAN ports, 2 WAN ports, DRAM 8 Mbytes, FLASH 2 Mbytes
        Configuration data is 28172/60000 bytes
        tftp daemon is configured.
        rlogin daemon is configured.
        telnet daemon is configured.
        BOOTP forwarding is disabled.
Port 0 :
        Ethernet Driver       Enabled
Port 1 :
        Frame Relay Driver    Enabled
Port 2 :
        Frame Relay Driver    Disabled
SR2501#
Line Protocol on Interface Serial2 changed state to DOWN
SR2501# ip
SR2501/IP# enable
IP instance is enabled.
SR2501/IP# int cr 210.103.102.254 255.255.255.192 0 bc
SR2501/IP# int en 0 0
SR2501/IP# int cr 172.30.19.50 255.255.255.252 1 bc
SR2501/IP# int en 0 1
SR2501/IP# sh int
Flag     IP address      IP mask         Port Type P2P-Neighbor    Status
------------------------------------------------------------------------
Enabled  172.30.19.50    255.255.255.252   1  BC   0.0.0.0         UP(40)
Enabled  210.103.102.254 255.255.255.192   0  BC   0.0.0.0         UP(0)
SR2501/IP# st add 0 0 128 1 172.30.19.49
SR2501/IP# fr
SR2501/FR# dlci add 1 16
The dlci(16) on the port 1 is already in use.
SR2501/FR# stack add 1 ip 16 172.30.19.49 disable
SR2501/FR# sh stack
    Port DLCI Network         Node Address      IARP Found VP#
    ---- ---- --------------- ----------------- ---- ----- ------------
IP   1    16 172.30.19.49    00:00:00:

SR2501/FR# saveall
SNMP is not running now.
RIP instance is not running.
OSPF instance is not running.
Spanning Tree is not running.
SR2501/FR# write
BLK#31 erased (delay=60468, 390ms)
SR2501/FR# ping 172.30.19.49
64 octets from 172.30.19.49: icmp_seq 0, time=6ms
64 octets from 172.30.19.49: icmp_seq 1, time=6ms
64 octets from 172.30.19.49: icmp_seq 2, time=6ms
64 octets from 172.30.19.49: icmp_seq 3, time=6ms
64 octets from 172.30.19.49: icmp_seq 4, time=6ms
64 octets from 172.30.19.49: icmp_seq 5, time=7ms
64 octets from 172.30.19.49: icmp_seq 6, time=7ms
64 octets from 172.30.19.49: icmp_seq 7, time=6ms
64 octets from 172.30.19.49: icmp_seq 8, time=6ms
64 octets from 172.30.19.49: icmp_seq 9, time=6ms
10 packets transmitted, 10 packets received.(0% packet loss)
round-trip (ms)  min/avg/max = 6/6/7
SR2501/FR# reset
Reinitializing Processor...!

Hi.
DRAM test...OK!
System Bootstrap, Version 1.0
Copyright (c) 1996 by SsangYong Infomation & Communications Corp.
i960 processor with 8 Mbytes of main memory

Downloading IOS ...from FLASH memory!
!source code format type is COFF
!.text:0x20010000(0xdd1cc) .data:0x200ed1d0(0xe488) .bss:0x200fb660(0x238150)
!<entry point> = 0x20010510

reading SR2501 configuration from NVRAM(60000) ... O.K.
wheap_start = [203337B0] maxaddr = [207FFFFF]
LAN port (0) Initializing ......OK.
WAN port (0) Initializing ......OK.
WAN port (1) Initializing ......OK.

                SsangYong Router System Ver. 4.3.5
                        Compiled at 30-MAY-2000 by YesHong

Copyright (C) 1995 RouterWare, Inc.
Copyright (C) 1995 RainbowBridge Communications Inc.
Copyright (C) 1995-1999 SsangYong Information & Communications Corp.

Buffers Initialized
Ethernet initialized
Frame Relay Initialized.
Device Drivers Initialized
IP Initialized.
NAT Disabled.
IPX Disabled.
Spanning Tree is disabled.
BOOTP Disabled.
SNMP disabled.
RIP Disabled.
OSPF Disabled.
Queuing Initialized
SR2501>
Interface Serial1 changed state to UP !
Line Protocol on Interface Serial1 changed state to UP
Frame Relay: Link state set to Up for port 0
Line Protocol on Interface Serial2 changed state to DOWN

저작자표시 비영리 변경금지

'도움글' 카테고리의 다른 글

DDos 악성봇 검사 사이트 (0)	2011.02.18
구형 메모리 식별방법 (0)	2011.02.18
USB에서 grub4dos,grub2 모두 올리기 (0)	2011.02.18
WiFi 암호 (0)	2011.02.18
DDR/DDR2/DDR3 RAM(메모리)차이점은? (4)	2011.02.18

만키로군 Blog